WireTech 5000P-10x Manual do Utilizador

6PSDSC-IP-5000P Series PSDR-5000-42S2 CAM + IP PSDR-5000-30S2 CAM Multi-Format Professional HDTV Processor User Manual Ver.

(1) Input Setup Set input parameters (2) Output Setup Set output parameters (3) System Set system parameters (4) Ethernet(optional) Set Ethern

LOCK indicator on front panel will turn green. LNB Frequency: Input LNB frequency Satellite Frequency: Input downstream frequency of satellite Symbo

only valid when the output smoothing is configured as Fixed Rate. 5.2 Outputs Menu Under Outputs Menu, you can monitor and configure the

press <EXIT>-key to scrap. Setup: under this sub menu, you can see all program names from the source of CI that was set in „CI Source‟ previou

source being selected, the TS will be delivered to the ASI output port on the back panel. Program: under this sub menu, you will see all program nam

this range: 0~99. Audio2 Mode: select Stereo, Left, Right or Mono for soundtracks. Audio2 Language: select the language of the audio. 5.2.4 ASI1 You

Mux Switch: the internal multiplexer could be switched On/Off. The default value is „off‟. To activate the re-Multiplexing function, you should turn

Stream Netmask: Enter the network sub mask for the subnet to which the unit is connected for IP streaming traffic. Stream Gateway: Set

Multicast IP: Enter the IP address of the IP stream for the transport stream over IP output. You can configure the IP stream output mode in M

input. 6-xxxxx displays the program name, which comes from MUX TS. All encrypted programs are labeled with a „$‟ sign on the first row. Press <EN

configure this address. Linux OS version: show Linux OS version ARM SW version: show ARM software version Decoder version: show Decoder version FPGA

5.4 Ethernet Menu There are four sub menus. 5.4.1 IP Out (Note this menu is showed only when the IP Out switch is enabled.) The TS/IP Ethernet

transport stream over IP. Uni/Multicast UDP port: Enter the UDP port number of the TS over IP stream. ProMPEG FEC: Enable/Disable: Enable or disabl

Note: If the TS contains PCR, you can select Auto mode. If not, please select Fixed rate. TS Bit rate: set the bit rate of the TS comes from the TS/

Input DVB-S2 QPSK/8PSK Demodulation Input frequency range 950~2150MHz Input level -65~-25dBm Input impedance 75Ω Connector F Connector Symb

Format Unframed Framing according to G.804 / G.752 (DS3) Output DS3 loop through output Connector 75

5000P-xx 1pc CD 1pc User Manual 1pc Power Cord 1pc RCA A/V Cable 1pc BNC Cable 1pc RS232-to-XRL cable

TS Bit Rate  set to the bit rate of incoming stream in experimental test, this value will be ignored by 5000P if “Output Smoothing = Auto” in previ

DVB mode: Uni/Multicast Setup  set the address and port parameters for the IP stream. Press Enter to go to the submenu. As below: Multicast IP  en

- 3 - Contents 1. Before Use the Device ...

5.4.3 Local IP setting ... 19 5.4.4 Ethernet statu

1. Before Use the Device Thank you for purchasing the 6PSDSC-IP-5000Pseries. This User Manual is written for operators/users of the 6PSDSC-IP-5000

2. Introduction As the latest version of NETKLA‟s flagship professional IRD, the 6PSDSC-IP-5000Pis full compliant with MPEG-2 (MP@ ML& MP@HL),

Video Format Output port Resolution SDI port 576I25 ,480I29.97, 1080I25, 1080I29.97, 1080I30 HDMI port 576I25 ,480I29.97,480P60, 576P50, 720P50,720

TS/IP IP input/output port RS-232 serial port for printing information ASI OUT1 Group1 ASI output port (one for back-up) ASI1 IN ASI1 inp

are connected well, then power can be applied to the device. The main socket and fuse are located at the rear panel of the device. When the device i